Replacement Part Numbers
| Item | Stock # | Description |
|---|---|---|
| 12340 Obsolete | MAGNETIC TORCH GUIDE (Straight Edge) | |
| OBSOLETE | 1011-B | SET SCREW, 8-32 (EACH) |
| 2611-N | 5″ CONNECTOR BODY MAGNETIC (EACH) | |
| 2911-N | CUTTING RAIL 24″ L | |
| 23040 | MAGNETIC TORCH GUIDE (Straight Edge) – NEW | |
| 2622-M | MAGNETIC BLOCK W/ SET SCREWS | |
| 2911-N | CUTTING RAIL 24′ L | |
| 4211 | THUMB SCREW 1/4-20 – LARGE | |
| Old Version | 4311 | SET SCREW 1/4-20 x 1/2 – LARGE |
| Old Version | FYI ONLY | HEX KEY 1/8′ |
| 24219 | CHARIOT CUTTING GUIDE | |
| 1011 | THUMB SCREW 10-24 x 1/2 (each) – SMALL | |
| 3211-2 | ROUND BUSHING HOUSING 2-hole | |
| 3311 | 5/16 HEX ARM (THREADED) X 15-1/2′ L | |
| Accessory | 3311-EX | 5/16 HEX ARM EXTENSION X 15-1/2′ L |
| 3511-B | 1/4′ BENT PIVOT PIN | |
| 3611 | 5/8′ SQ. HOLDER | |
| 3711 | TORCH TOP BUSHING (UNIVERSAL) | |
| 3811 | WHEELS (each) | |
| 3911 | 5/8′ SQ. MAIN BODY (for axle) | |
| 4011 | AXLE, KNURLED (each) | |
| 4001 | BRONZE AXLE BUSHING | |
| 4100 | 1/4′ ADJUSTMENT PIN | |
| 4211 | THUMB SCREW 1/4-20 – LARGE | |
| 4411 | JAM NUTS (each) | |
| 5815 | SNAP RING, 3/4′ EXTERIOR | |
| FYI ONLY | SET SCREW, 8-32 x 3/8′ L HEX HEAD | |
| 28439 | MAGNETIC CIRCLE LAYOUT & BURNING GUIDE | |
| 1011 | THUMB SCREW 10-24 x 1/2 (each)- SMALL | |
| 3100 | ROUND MAGNETIC w/ DEGREES | |
| 3211-1 | ROUND BUSHING HOUSING 1-hole | |
| 3311 | 5/16 HEX ARM THREADED X 15-1/2′ L | |
| Accessory | 3311-EX | 5/16 HEX ARM EXTENSION X 15-1/2′ L |
| 3411 | 5/8 SQ. POINT PIN HOLDER (BRASS) | |
| 3511 | 1/4′ PIVOT PIN (straight) | |
| 3611 | 5/8 SQ. HOLDER | |
| 3711 | TORCH TIP BUSHING (UNIVERSAL) | |
| 5815 | SNAP RING, 3/4′ EXTERIOR | |
| 3-28 | MAGNETIC BLOCKS (SET OF 3) | |
| 1011 | THUMB SCREW 10-24 x 1/2 (each)-SMALL | |
| Old Version | 1011-B | SET SCREW, 8-32 (each) |
| 2811 | SUPPORT BODY w/ MAGNET (each) | |
| 30061 | PLASMA WIZ | |
| 1011 | THUMB SCREW 10-24 x 1/2 (each)-SMALL | |
| 3311-S | 5/16′ x 5-1/2’L SHORT HEX ARM | |
| 3511-B | 1/4′ BENT PIVOT PIN | |
| 3611 | 5/8 SQ. HOLDER | |
| 6611 | MAIN BODY (bushing housing – no slots) | |
| 38240 | PIPE FLANGE ALIGHNER, TENSION | |
| 1111 | ARM ASSEMBLY W/ VIAL | |
| 2111 | PIN W/ STEM & VIAL | |
| 3111 | PIN W/ STEM & without VIAL | |
| 4111 | KNURLED NUT (each) | |
| 5111 | VIAL 1’L (each) | |
| 6111 | RUBBER ENDS (pair) | |
| 38240-T | PIPE FLANGE ALIGNER, THREADED | |
| 0501 | STUD, DBL LEAD 1/2-13 x 2-7/8′ L | |
| 1111 | ARM ASSEMBLY w/VIAL | |
| 2111-T | PIN w/ STEM & VIAL | |
| 3111-T | PIN w/ STEM & without VIAL | |
| 4111-T | KNURLED NUT (each) | |
| 5111 | VIAL 1′ L (each) | |
| 6111 | RUBBER ENDS (pair) | |
| 38240-TL | PIPE FLANGE ALIGNER, THREADED LRG | |
| 0503 | STUD, DBL LEAD 1/2-13 x 4-1/2′ L | |
| 1111-L | ARM ASSEMBLY w/ VIAL | |
| 2111-TL | PIN w/ STEM & VIAL | |
| 3111-TL | PIN w/ STEM & without VIAL | |
| 4111-TL | KNURLED NUT (each) | |
| 5111 | VIAL 1′ L (each) | |
| 6111 | RUBBER ENDS (pair) | |
| 42050 | TWO HOLE PINS, TENSION | |
| 4111 | KNURLED NUT (each) | |
| 5111 | VIAL 1′ L (each) | |
| 7111 | PIN w/ STEM & VIAL | |
| 8111 | PIN w/ STEM & witout VIAL | |
| 42050-T | TWO HOLE PIN, THREADED | |
| 0501 | STUD, DBL LEAD 1/2-13 x 2-7/8′ L | |
| 4111-T | KNURLED NUT (each) | |
| 5111 | VIAL 1′ L (each) | |
| 7111-T | PIN w/ STEM & VIAL | |
| 8111-T | PIN w/ STEM & without VIAL | |
| 42050-TL | TWO HOLE PIN, LARGE THREADED | |
| 0503 | STUD, DBL LEAD 1/2-13 x 4-1/2′ L | |
| 4111-TL | KNURLED NUT (each) | |
| 5111 | VIAL 1′ L (each) | |
| 7111-TL | PIN w/ STEM & VIAL | |
| 8111-TL | PIN w/ STEM & without VIAL | |
| 42050-TXL | TWO HOLE PIN, THREADED EX-LRG IN CARRYING CASE | |
| 0503 | STUD, DBL LEAD 1/2-13 x 4-1/2′ L | |
| 0503-EX | EXTENSION COUPLING | |
| 4111-TXL | KNURLED NUT, X-LARGE THREADED | |
| 8111-TXL | PIN w/ STEM- EX. LRG | |
| 8902 | CARRYING CASE, 13’L x 8’W x 3’DEEP | |
| 5102 | VIAL REPAIR KIT | |
| 5102 | VIAL 1′ L (2 EA.) + TUBE OF SEALANT | |
| 53025-M | SMALL CENTERING HEAD-MAGNETIC | |
| 1711 | DEGREE DIAL w/ VIAL | |
| 2111-S | SMALL MAIN BODY UNIT | |
| 2311 | CENTER PUNCH, SMALL | |
| 6311 | 2.5 DEGREE STICKER | |
| 53076-M | STANDARD CENTERING HEAD – MAGNETIC | |
| 1711 | DEGREE VIAL w/ VIAL | |
| 2111-L | “Y” TYPE BASE UNIT | |
| 2311-L | CENTER PUNCH PIN | |
| 6311 | 2.5 DEGREE STICKER | |
| 6201 | PLASMA BEVELING YOKE-ACCESSORY | |
| 1011 | THUMB SCREW 10-24 x 1/2 (EACH) SMALL ( each) | |
| 1211 | STAND-OFF SCREW 1/4-20 x 1.00″ (each) | |
| 5911 | ADJUSTING SCREW 1/4-20 x 1/2″ (each) | |
| 63803 | MITER MARKER IN CARRYING CASE | |
| 1011-B | SET SCREW, 8-32 (each) | |
| 5015 | MAIN BODY w/ MAGNETIC LEGS & VIAL | |
| 5111 | VIAL 1′ L (each) | |
| 5115 | 1/2′ ROUND SHAFT w/ ARM HOLDER | |
| 5215 | MARKING ARM w/ DEGREE PAD | |
| 5311 | SET COLLAR w/ SCREW | |
| 5511 | KNOB w/ MALE THREADS w/ WASHER | |
| 5515 | KNOB-Small (female threads) w/ WASHER | |
| 6380-L | MAGNETIC LEGS w/ SCREWS (each) | |
| 8311 | STRUCTURAL ADAPTOR | |
| 8903 | CASE, LOCKABLE, POLYPROPYLENE | |
| FYI ONLY | WAVE WASHER 1/4′ | |
| FYI ONLY | WASHER 1/4′ FLAT | |
| 65007 | MULTI-HOLE IMAGER | |
| 1112 | ROD, 15′ LONG X 3/8′ DIAMETER | |
| 1113 | “ON & OFF” MAGNETIC BASE | |
| 1114 | VERTICAL POST, 1′ DIAMETER | |
| 1115 | CIRCULAR VIAL | |
| 1116 | HORIZONAL ARM, MAIN IMAGER | |
| 1117 | DEGREE ROD HOLDER ASSEMBLY | |
| 1118 | MARKING ARM w/ SOAPSTONE ASSEMBLY | |
| 1119 | SLIDING MARKING ARM HOLDER | |
| 4211 | THUMB SCREW, 1/4-20 – LARGE | |
| 5411 | KNOB-LARGE (female threads) w/ WASHER | |
| 5515 | KNOB-SMALL (female threads) w/ WASHER | |
| 8903 | CASE, 16’L X 6’W X 3’DEEP | |
| 1011-B | SET SCREW, 8-32 (each) | |
| 70001 | MULTI-USE ANGLE BURNING GUIDE | |
| 1022 | SET SCREW, 1/4-20 x 1/4’L HEX HEAD | |
| 5411 | KNOB-LARGE (female threads) w/ WASHER | |
| 7011 | MAIN LRG. BASE (w/ brass pivot pin & magnets) | |
| 7100 | BURNING RAIL HOLDER w/ DEGREES | |
| 7211 | BURNING RAIL 16′ L STAINLESS | |
| 7211-SP | BURNING RAIL – SPECIAL LENGTH (inch) | |
| FYI ONLY | WAVE WASHER 1/4′ | |
| FYI ONLY | WASHER 1/4′ FLAT | |
| FYI ONLY | HEX KEY 1/8′ | |
| 89754 | UNIVERSAL MAGNETIC TAPE HOLDER | |
| 5111 | VIAL 1’L (each) | |
| CW-300 | CIRCLE WIZ | |
| 1011 | THUMB SCREW 10-24 x 1/2 (each)-SMALL | |
| 3211 | ROUND BUSHING HOUSING | |
| 3311-S | 5/16′ x 5-1/2’L SHORT HEX ARM | |
| 3511-B | 1/4′ BENT PIVOT PIN | |
| 3611 | 5/8′ SQ. HOLDER | |
| 3711 | TORCH TIP BUSHING (universal) | |
| 5815 | SNAP RING, 3/44′ EXTERIOR | |
| FYI ONLY | NUT 1/4-20 | |
| FYI ONLY | SET SCREW 8-32 | |
| FYI ONLY | HEX KEY 5/64′ | |
| L-2 | ACCESSORY DEGREE LEVEL | |
| 1711 | DEGREE DIAL w/ VIAL | |
| 1811 | SCREW & FRICTION WASHER | |
| 2511 | MAIN BODY UNIT | |
| 6311 | 2.5 DEGREE STICKER | |
| MM-501 | MASTER MARKER (REPLACES MM-500) | |
| 1011-B | SET SCREW, 8-32 (each) | |
| 5011 | MAIN BODY w/ MAGNETS & VIAL – NEW | |
| 5101 | 1/2 ROUND SHAFT w/ ARM HOLDER | |
| 5111 | VIAL 1′ L (each) | |
| 5211 | MARKING ARM w/ DEGREE PAD | |
| 5311 | SET COLLAR w/ SCREW | |
| 5411 | KNOB (female threads) w/ WASHER | |
| 5511 | KNOB w/ MALE THREADS w/ WASHER | |
| 6111-MM | STRUCTURAL ADAPTOR | |
| FYI ONLY | WAVE WASHER 1/4′ | |
| FYI ONLY | WASHER 1/4′ FLAT | |
| PG-601 | PLASMA CUTTING GUIDE | |
| 1011 | THUMB SCREW 10-24 x 1/2 (each) SMALL | |
| 3311 | 5/16 HEX ARM x 15-1/2’L | |
| Accessory | 3311-EX | 5/16 HEX ARM EXTENSION X 15-1/2′ L |
| 3511-B | 1/4′ BENT PIVOT PIN | |
| 3611 | 5/8 SQ. HOLDER | |
| 3811 | WHEELS (each) | |
| 4011 | AXLE, KNURLED (each) | |
| 4001 | BRONZE AXLE BUSHING (each) | |
| 4411 | JAM NUTS (each) | |
| 5611 | MAIN BODY (bushing housing with slots) | |
| 5711 | WHEEL ADJUSTMENT BRACKET (each) | |
| 5811 | SNAP RING, 1-3/8′ | |
| 5911 | 1/4-20 ADJUSTING SCREW (each) | |
| Accessory | 7511 | SUCTION CUP FOR 77350 Acces. Base (each) |
| Accessory | 7711 | MAGNETIC BASE w/ Straight Pin |
| PP-200 | POCKET PRO LEVEL | |
| 1711 | DEGREE DIAL w/ VIAL | |
| 1811 | SCREW & FRICTION WASHER | |
| 2000 | MAIN LEVEL BODY | |
| 5111 | VIAL 1′ L (each) | |
| 6311 | 2.5 DEGREE STICKER | |
| SL-100 | STANDARD POCKET LEVEL | |
| 5111 | VIAL 1″ L (each) |
Pipe Layout Tools